設定に再起動が必要なコンフィグまとめ
Cisco
ISR4000 / ASR1000
ASR1000 : license boot level {adventerprise | advipservices |ipbase} [1]
- Universal イメージの IOS / IOS-XE はコマンドでライセンス レベルを変更可能
ISR4000 : platform hardware throughput level { 2500000 | 5000000} [2]
ISR4000 : platform hardware throughput level boost [3]
ASR1000 : platform hardware throughput level [4]
- デフォルトは双方向で合計 2.5Gbps のスループット
- 最大双方向で 20Gbps のスループットを設定可能
- CSR1000V は再起動が不要と記載あり
ASR1001-HX : platform hardware crypto-throughput level { 8g | 8-16g } [5]
- こちらは再起動が必要無いように読める
ASR1002-HX : platform hardware crypto-throughput level { 8g | 8-16g | 8-25g | 16-25g } [6]
- こちらは再起動が必要無いように読める
Catalyst 6500 Sup720
mls cef maximum-routes [7]
Catalyst 2960 / 3750 / 3560
3750 : sdm prefer { access | default | dual-ipv4-and-ipv6 { default | routing | vlan } | indirect-ipv4-and-ipv6-routing | routing | vlan } [8]
- PBR はデフォルトで TCAM が割り当てられていないため、routing テンプレートに変更 ＋ 再起動が必要
Catalyst 3850 / 3650 / 9000
license boot level <license_level> [9]
- Universal イメージの IOS / IOS-XE はコマンドでライセンス レベルを変更可能
9500 : sdm prefer { core | nat | distribution | custom } [10]
- 9500H は MAC アドレステーブルや ARP などがデフォルトの Core テンプレートで少ないため、Distribution に変更するケースがあります
Nexus 9300
max-metric router-lsa external-lsa include-stub on-startup summary-lsa
- コマンド投入時、次回の再起動時に有効になる旨のメッセージが表示されます
- ただ、これは起動時に発動するコマンドのため、reload が必要とは違う気がします
Juniper
MX204
set chassis fpc <fpc_num> pic <pic_num> port <port_num> speed <speed> [11]
- シャーシ全体の再起動 + Junos 起動は必要^無いけど、両方の PIC = 全ポートが reset されるため要注意
Arista
7050X3
zerotouch cancel [12]
- 最初は startup-config が存在しないため、ZTP モードで起動する
- cancel すると自動で再起動がかかる
service routing protocols model { ribd | multi-agent } [13]
- 2022/09 現在は ribd がデフォルト
- 最近は multi-agent を使うのが主流
- EVPN などでは multi-agent を使用する必要がある
DCS-7280R, DCS-7280R2, DCS-7500R, DCS-7500R2, DCS-7020R
hardware access-list mechanism tcam [14]
A10
Thunder 3030S CGN
system resource-usage nat-pool-addr-count [15]
- CGN 用 NAT プールアドレス
Thunder 3040S CFW
system resource-usage nat-pool-addr-count [16]
cgnv6 resource-usage lsn-nat-addr-count [17] [18]
- こちらはコマンドリファレンスに reload 必須との記載が無いが、コマンドを打つと reload が必要と出てくる
リファレンス
- ↑ Chapter: License Verification https://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/1001HX_1002HX/b_ASR1001HX-1002HX_HIG/b_ASR1001HX-1002HX_HIG_chapter_0110.html license boot level <License_Level>
- ↑ Performance https://www.cisco.com/c/en/us/td/docs/routers/access/4400/software/configuration/guide/isr4400swcfg/bm_isr_4400_sw_config_guide_chapter_0101.html#concept_3F15D3B0CBA64CA9BADC3C84FE0C63FB To configure the throughput level, perform the following steps and to upgrade the throughput level use the platform hardware throughput level { 2500000 | 5000000} command. In the user EXEC configuration mode, enter the enable command. Enter configure terminal command to enter the global configuration mode. To upgrade the throughput level, enter the platform hardware throughput level{2500000|5000000} command. To exit global configuration mode, enter exit. To save the configuration, enter the copy running-config startup-config command. To reload the router enter reload. A reload is required to activate the throughput level.
- ↑ platform hardware throughput level boost https://www.cisco.com/c/en/us/td/docs/routers/access/4400/software/configuration/guide/isr4400swcfg/bm_isr_4400_sw_config_guide_chapter_0101.html#concept_x2p_pkj_ndb Save the configuration and reload the device to enable Boost performance license. After the reload, the Boost Performance is activated as shown in this example.
- ↑ スループット レベルの設定 https://www.cisco.com/c/ja_jp/td/docs/routers/asr1000/install/guide/1001-x/asr1hig-book/asr1hig-book_chapter_0101.html#con_1060881 Cisco ASR 1001-X ルータの組み込みエンベデッド サービス プロセッサは、ソフトウェア ライセンスに応じて、2.5 Gbps（デフォルト）、5 Gbps、10 Gbps、および 20 Gbps のスループットをサポートします。 ソフトウェア アクティベーションによるパフォーマンス アップグレード ライセンスを適用してから、ルータをリロードすることによって、ESP のスループットを 2.5 Gbps（デフォルト）から 5 Gbps にアップグレードできます。ESP のスループットは、任意のライセンス レベルから別のライセンス レベルにアップグレードできます。 ESP の現在のスループットレベルを決定するには、show platform hardware throughput level コマンドを実行します。 次に、20 Gbps パフォーマンス アップグレード ライセンスの適用とルータのリロード後の このコマンドの出力例を示します。
- ↑ 暗号化スループット レベルの設定https://www.cisco.com/c/ja_jp/td/docs/routers/asr1000/install/guide/1001HX_1002HX/b_ASR1001HX-1002HX_HIG.pdf
Cisco ASR 1001-HX ルータの暗号化スループット レベルを設定するには、次のコマンドを入力します。
Router(config)# platform hardware crypto-throughput level ? 8-16g crypto throughput upgrade, bits per second 8g crypto throughput level, bits per second Router(config)# platform hardware crypto-throughput level 8g % Crypto Bandwidth set to 8G bps. Router(config)# platform hardware crypto-throughput level 8-16g % Crypto Bandwidth set to 16G bps.
- ↑ 暗号化スループット レベルの設定https://www.cisco.com/c/ja_jp/td/docs/routers/asr1000/install/guide/1001HX_1002HX/b_ASR1001HX-1002HX_HIG.pdf
Cisco ASR 1002-HX ルータの暗号化スループット レベルを設定するには、次のコマンドを入力します。
Router(config)# platform hardware crypto-throughput level ? 16-25g crypto throughput upgrade, bits per second 8-16g crypto throughput upgrade, bits per second 8-25g crypto throughput upgrade, bits per second 8g crypto throughput level, bits per second
- ↑ CAT 6500 and 7600 Series Routers and Switches TCAM Allocation Adjustment Procedures https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/117712-problemsolution-cat6500-00.html#anc3 You can enter the mls cef maximum-routes ip <number in thousands> command in order to adjust the number of routing entries that are allocated to the IPv4. This does not increase the overall size of the FIB TCAM, but it reduces the number of routing entries that are allocated to the IPv6 in order to increase the amount of TCAM space for the IPv4.
- ↑ Chapter: Configuring SDM Templates https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/15-0_2_se/configuration/guide/3750x_cg/swsdm.html
- ↑ Configuring Base and Add-On Licenses https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/17-6/configuration_guide/sys_mgmt/b_176_sys_mgmt_9300_cg/licenses.html#Cisco_Task.dita_f126c327-a647-4235-b1a2-930771e49f9d license boot level <license_level>
- ↑ Chapter: Configuring SDM Templates https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9500/software/release/17-6/configuration_guide/sys_mgmt/b_176_sys_mgmt_9500_cg/configuring_sdm_templates.html
- ↑ Port Speed on MX204 Overviewhttps://www.juniper.net/documentation/us/en/software/junos/interfaces-ethernet/topics/topic-map/port-speed-configuration.html#concept-mx204 To change the default speed, you must select a port and configure a different port speed on it and reset both the PICs for the configuration to take effect. For example, select 40GE or 100GE on PIC0 and 10GE on PIC1. For this configuration to take effect, you must reset both PICs.
- ↑ Canceling Zero Touch Provisioning https://www.arista.com/en/um-eos/eos-initial-switch-access#xx1131266 To avoid entering ZTP mode on subsequent reboots, create a startup-config file as described in Step 8 of Ethernet Management Port.
- ↑
localhost(config)#service routing protocols model multi-agent ! Change will take effect only after switch reboot localhost(config)# - ↑ Support for Private VLAN https://www.arista.com/en/um-eos/eos-virtual-lans-vlans?searchword=reload On DCS-7280R, DCS-7280R2, DCS-7500R, DCS-7500R2, DCS-7020R Private VLAN and Algomatch features are mutually exclusive. Disable algomatch with the hardware access-list mechanism tcam command . Note that this requires a reload of the system to take effect.
- ↑ system resource-usage https://documentation.a10networks.com/ACOS/271x/271-P6/ACOS_2_7_1-P6/html/ax-cli-reference-Responsive%20HTML5/ax-cli-reference/ax-cli-globalcfg-cmds/system_resource-usage.htm?rhsearch=system%20resource-usage%20nat-pool-addr-count&rhsyns=%20 nat-pool-addr-count --- Total IP source NAT pools Reload or Reboot Required To place a change to l4-session-count into effect, a reboot is required. A reload will not place this change into effect. For changes to any of the other system resources, a reload is required but a reboot is not required.
- ↑ system resource-usage https://documentation.a10networks.com/ACOS/414x/ACOS_4_1_4-GR1-P1/html/cli-reference-Responsive%20HTML5/cli-reference/cli-globalcfg-cmds/system_resource-usage.htm?rhsearch=system%20resource-usage&rhsyns=%20 nat-pool-addr-count num --- Total number of NAT pool addresses available for configuration in the system. The range is platform specific. Usage To place a change to l4-session-count into effect, a reboot is required. A reload will not place this change into effect. For changes to any of the other system resources, a reload is required but a reboot is not required.
- ↑ cgnv6 resource-usage https://documentation.a10networks.com/ACOS/414x/ACOS_4_1_4-GR1-P11/html/cliv6-Responsive%20HTML5/cliv6/cliv6_cgn_aka_lsn_cmds/cgnv6_resource-usage.htm?rhsearch=cgnv6%20resource-usage%20lsn-nat-addr-count&rhsyns=%20
- ↑
(config)#cgnv6 resource-usage lsn-nat-addr-count 2048 Changes will come into effect next time you reload the Software.